The B200S-WH and B200S-IV sounder bases are used with addressable detector heads. For a list of compatible sensors, refer to the System Sensor website at www.systemsensor.com. Refer to the appropriate manual for more information on sensors. The B200S-WH and B200S-IV sounder bases were designed specifically to meet the needs of dwelling unit applications. They offer maximum flexibility in configuration and operation to meet or exceed the requirements of UL268 and UL464. The sounder base is capable of producing a variety of tone patterns, including the distinctive three-pulse temporal pattern (ANSI Temporal 3) fire alarm signal now required by NFPA 72 for commercial and residential applications. The B200S-WH/B200S-IV can be commanded by the Fire Alarm Control Panel to adopt the address of the attached sensor head, but as a unique device type on the loop. By using the address, the fire alarm control panel can command an individual sounder base to activate, or a group of sounders in a suite or other multi-room configuration. The command set from the panel can be tailored to the specific event, allowing selection of volume, tone, and group. The device offers two volume levels: 75 dBA and 85 dBA. The available tones are Continuous, ANSI Temporal 3, ANSI Temporal 4, and March Time. In addition, some fire alarm panels will offer the ability to command a custom tone pattern. Refer to the appropriate fire alarm control panel manual for more information.

The RE 317D-SL addressable detectors are designed to work with Avani Panel. These detectors are low profile and O have dual LED’s for 360 visual indication. The LED’s are blinking in normal operating condition whereas the steady state indicates fire status. It has an unique chamber designed to sense smoke produced by wide range of sources of combustion. The detectors sensitivity can be programmed through fire alarm control panel. It has a unique drift compensation where the detector adjusts its normal reference based on environment conditions.

The RE 337H addressable detectors are designed to work with Avani Panel. These detectors are low profile and have dual LED’s for 360 visual indication. The LED’s are blinking in normal operating condition whereas the steady state indicates fire status.

Detector addressing is electronically programmed into the detector at the time of installation.

RE 337H is a fixed cum rate of rise heat detector using a thermistor. These detectors will raise an alarm when the detector reaches 59 C(Fixed) or when the change in temperature exceeds the rate of rise of 11 C / min

Features:

We are engaged in offering Conventional Sounder Cum Strobe to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering JTY-GD-2330/B Stand Alone Smoke Detectors to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering G1AVRF EST Edward Sounder Horn Cum Strobe to our clients. Our range of all products is widely appreciated by our clients.

The FRM-1 Relay Control Module is intended for use in intelligent, two-wire systems where the individual address of each module is selected using the built-in rotary switches. It allows a compatible control panel to switch discrete contacts by code command. The relay contains two isolated sets of Form-C contacts, which operate as a DPDT switch and are rated in accordance with the table in the manual. Circuit connections to the relay contacts are not supervised by the module. The module also has a panel controlled LED indicator. This module can be used to replace a CMX-2 module that has been configured for Form-C operation.

The Morley-IAS repeaters are compact remote control units for Morley-IAS intelligent multi protocol fire alarm control panels. These units, along with other I/O peripheral devices and theexternal printer further enhance the flexibility and functionality of our fire alarm control panel range.

The repeaters provide an extension to the operation of the fire alarm control panel. There are two types available - passive with indications only and no controls, or active with both controls and indicators. Both display the operational state of the control panel using the 80 character LCD display and the 7 LED status indicators.

In addition to the general status indicators the Active repeater is fitted with key operated "Access Enable" switch for the control functions. Individual buttons are provided for System Reset, Mute, Accept, Sound Alarms, Silence/Re-sound Alarms and Self test. Thus enabling control functions to be duplicated in strategic locations around the installation.