J P Fire Safety

The FRM-1 Relay Control Module is intended for use in intelligent, two-wire systems where the individual address of each module is selected using the built-in rotary switches. It allows a compatible control panel to switch discrete contacts by code command. The relay contains two isolated sets of Form-C contacts, which operate as a DPDT switch and are rated in accordance with the table in the manual. Circuit connections to the relay contacts are not supervised by the module. The module also has a panel controlled LED indicator. This module can be used to replace a CMX-2 module that has been configured for Form-C operation.

The LCM-320 Loop Control Module and the LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM-320s and five LEM-320s. The LEM-320 module is used to expand the NFS-640/NFS2-640 to a second loop, and to expand each LCM-320 used on the NFS-3030/NFS2-3030 — each NFS-3030/NFS2-3030 LCM-320 supports an expansion LEM-320.

We are engaged in offering Notifier NFS-320 Loop Panel to our clients. Our range of all products is widely appreciated by our clients.

The Notifier ISO-X(A) Fault Isolator Module is used with Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs) to protect the system against wire-to-wire short circuits on the SLC loops.

Features:

• Powered by SLC loop directly, no external power required.
• Base mounts on standard junction boxes (4.0"/10.16 cm square by 2.125"/5.398 cm deep).
• Integral LED blinks to indicate normal condition. Illuminates steady when short circuit condition is detected.
• High noise (EMF/RFI) immunity.
• Wide viewing angle of LED.
• SEMS screws with clamping plates for ease of wiring.
• Opens SLC loop automatically on detection of short, preventing the short from causing failure of the entire loop.
• Automatically resets on correction of short.
• Supports Style 4, 6, or 7 wiring.

We are engaged in offering Notifier FRM-1 Relay Module to our clients. Our range of all products is widely appreciated by our clients.

The LCM-320 Notifier Loop Control Module and the LEM-320 Notifier Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM320s and five LEM-320s. The LEM-320 module is used to expand the NFS-640/NFS2-640 to a second loop, and to expand each LCM-320 used on the NFS-3030/NFS2-3030 — each NFS-3030/NFS2-3030 LCM-320 supports an expansion LEM-320.

• Up to 12,500 feet (3,810 m) on a Class B (Style 4) SLC loop (twisted-unshielded).
• Built-in degraded mode increases survivability.
• Very simple installation — plug-in style.
• Permits multiple loops in small enclosure.

General The NFS2-3030 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. Fire emergency detection and evacuation are extremely critical to life safety, and the NFS2-3030 is ideally suited for these applications. The NFS2-3030 is part of the ONYX® Series of products from NOTIFIER. The NFS2- 3030 is ideal for virtually any application because it features a modular design that is configured per project requirements. With one to ten Signaling Line Circuits (SLCs), the NFS2-3030 supports up to 3,180 intelligent addressable devices. Information is critical to fire evacuation personnel, and the NFS2- 3030’s large 640-character Liquid Crystal Display (LCD) presents vital information to operators concerning a fire situation, fire progression, and evacuation details. A host of other options are available, including single- or multi-channel voice; firefighter’s telephone; LED, LCD, or PC-based graphic annunciators; networking; advanced detection products for challenging environments; wireless fire protection; and many additional options. 

Features:

• Certified for seismic applications when used with the appropriate seismic mounting kit. 
• Approved for Marine applications when a marine-listed version is used with marine-listed compatible equipment. See DN-60688. 
• Complies with UL 2572 Mass Notification Systems (NFS2-3030 version 20 or higher). 
• One to ten isolated intelligent Signaling Line Circuits (SLC) Class A, B, or X. 
• Wireless fire protection using SWIFT Smart Wireless Integrated Fire Technology. See DN-60820. 
• Up to 159 detectors and 159 modules per SLC; 318 devices per loop/3,180 per FACP or network node.
• Detectors can be any mix of ion, photo, thermal, or multi-sensor; wireless detectors are available for use with the FWSG. 
• Modules include addressable pull stations, normally open contact devices, two-wire smoke detectors, notification, or relay; wireless modules are available for use with the FWSG. 
• Large 16 line, 640 character LCD backlit display or use displayless as a network node. 

Network options: 

• High-speed network for up to 200 nodes (NFS2-3030, NFS2- 640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NFS-3030, NFS-640, and NCA). 
• Standard network for up to 103 nodes (NFS2-3030, NFS2-640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NCS, NFS-3030, NFS-640, NCA, AFP-200, AFP300/400, AFP-1010, and AM2020). Up to 54 nodes when DVCEM is used in network paging. 
• Built-in Alarm, Trouble, Security, and Supervisory relays. 
• VeriFire® Tools online/offline program option. 
• With built-in Degraded Mode operation, the system is capable of general alarm if a fire alarm condition is present even if the central processing unit (CPU) fails. 
• Weekly Occupancy Schedules allow changing sensitivity by time of day and day of week. 
• EIA-485 annunciators, including custom graphics.

NFS2-320 NOTIFER General The NFS-320 intelligent Fire Alarm Control Panel is part of the ONYX® Series of Fire Alarm Controls from NOTIFIER. In stand-alone or network configurations, ONYX Series products meet virtually every application requirement. The NFS-320’s modular design makes system planning easier. The panel can be configured with just a few devices for small building applications, or networked with many devices to protect a large campus or a high-rise office block. Simply add additional peripheral equipment to suit the application. Wireless fire protection can be added with the SWIFT wireless gateway and devices. For installations using NFS-320C, an optional ACM Series annunciator can be mounted in the same cabinet (up to 48 zones/points, order separately; see DN-60085). NOTE: Unless called out with a version-specific “R”, “C” or “E” at the end of the part number, “NFS-320” refers to models NFS-320, NFS-320R, NFS-320C, and NFS-320E. 

Features:

• Certified for seismic applications when used with the appropriate seismic mounting kit. 
• Approved for Marine applications when used with listed compatible equipment. See DN-60688. 
• One isolated intelligent Signaling Line Circuit (SLC) Class A, B, or X. 
• Up to 159 detectors and 159 modules per SLC; 318 devices maximum.
• Detectors can be any mix of ion, photo, thermal, or multi-sensor; wireless detectors are available for use with the FWSG.
• Modules include addressable pull stations, normally open contact devices, two-wire smoke detectors, notification, or relay; wireless modules are available for use with the FWSG. 
• Optional FWSG Wireless SWIFT Gateway supports wireless SLC devices. 
• Standard 80-character display. 

Network options: 

• High-speed network for up to 200 nodes (NFS2-3030, NFS2- 640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NFS-3030, NFS-640, and NCA). 
• Standard network for up to 103 nodes (NFS2-3030, NFS2-640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NCS, NFS-3030, NFS-640, NCA, AFP-200, AFP-300/ 400, AFP-1010, and AM2020). Up to 54 nodes when DVC-EM is used in network paging. 
• 6.0 A power supply with four Class A/B built-in Notification Appliance Circuits (NAC). Selectable System Sensor, Wheelock, or Gentex strobe synchronization. 
• Built-in Alarm, Trouble, Security, and Supervisory relays. 
• VeriFire® Tools online or offline programming utility. Upload/ Download, save, store, check, compare, and simulate panel databases. Upgrade panel firmware. 
• Autoprogramming and Walk Test reports. 
• Multiple central station communication options: – Standard UDACT – Internet – Internet/GSM 
• 80-character remote annunciators (up to 32). 
• EIA-485 annunciators, including custom graphics

We are engaged in offering Notifier NFS-320 Single Loop Panel to our clients. Our range of all products is widely appreciated by our clients.

General The NFS2-320 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. Fire emergency detection and evacuation are extremely critical to life safety, and the NFS2-3030 is ideally suited for these applications. The NFS2-3030 is part of the ONYX® Series of products from NOTIFIER. The NFS2- 3030 is ideal for virtually any application because it features a modular design that is configured per project requirements. With one to ten Signaling Line Circuits (SLCs), the NFS2-3030 supports up to 3,180 intelligent addressable devices. Information is critical to fire evacuation personnel, and the NFS2- 3030’s large 640-character Liquid Crystal Display (LCD) presents vital information to operators concerning a fire situation, fire progression, and evacuation details. A host of other options are available, including single- or multi-channel voice; firefighter’s telephone; LED, LCD, or PC-based graphic annunciators; networking; advanced detection products for challenging environments; wireless fire protection; and many additional options. 
Features:

• Certified for seismic applications when used with the appropriate seismic mounting kit. 
• Approved for Marine applications when a marine-listed version is used with marine-listed compatible equipment. See DN-60688. 
• Complies with UL 2572 Mass Notification Systems (NFS2-3030 version 20 or higher). 
• One to ten isolated intelligent Signaling Line Circuits (SLC) Class A, B, or X. 
• Wireless fire protection using SWIFT Smart Wireless Integrated Fire Technology. See DN-60820. 
• Up to 159 detectors and 159 modules per SLC; 318 devices per loop/3,180 per FACP or network node. 
• Detectors can be any mix of ion, photo, thermal, or multi-sensor; wireless detectors are available for use with the FWSG. – Modules include addressable pull stations, normally open contact devices, two-wire smoke detectors, notification, or relay; wireless modules are available for use with the FWSG. 
• Large 16 line, 640 character LCD backlit display or use displayless as a network node. 

Network options: 

• High-speed network for up to 200 nodes (NFS2-3030, NFS2- 640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NFS-3030, NFS-640, and NCA).
• Standard network for up to 103 nodes (NFS2-3030, NFS2-640, NFS-320(C), NFS-320SYS, NCD, NCA-2, DVC-EM, ONYXWorks, NCS, NFS-3030, NFS-640, NCA, AFP-200, AFP300/400, AFP-1010, and AM2020). Up to 54 nodes when DVCEM is used in network paging. 
• Built-in Alarm, Trouble, Security, and Supervisory relays. 
• VeriFire® Tools online/offline program option. 
• With built-in Degraded Mode operation, the system is capable of general alarm if a fire alarm condition is present even if the central processing unit (CPU) fails. 
• Weekly Occupancy Schedules allow changing sensitivity by time of day and day of week. 
• EIA-485 annunciators, including custom graphics.

Notifier FSP-851(A) Series intelligent plug-in smoke detectors with integral communication provide features that surpass conventional detectors. Detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. The FSP-851(A) photoelectric detector’s unique optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources. Dual electronic thermistors add 135°F (57°C) fixedtemperature thermal sensing on the FSP-851T(A). The FSP851R(A) is a remote test capable detector for use with DNR(A)/DNRW duct detector housings. FSP-851(A) series detectors are compatible with Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs)

N16e/x Fire Alarm Control Panel EFFICIENT, SCALABLE, CONNECTED General The NOTIFIER INSPIRE™ Series Fire Alarm Control Panels (FACPs) bring the latest technology to life safety. Fire emergency detection and evacuation are extremely critical to life safety. With the N16e and N16x panels, NOTIFIER INSPIRE Series offers a scalable platform to meet any size application. NOTIFIER INSPIRE Series FACPs feature an intuitive 10" color touchscreen display. This display is color coded with system and status information. Users are presented with vital information that is easy to read and navigate. Offered in a standard preconfigured enclosure, the N16e comes with one Signaling Line Module to support 318 intelligent addressable devices. Up two additional Signaling Line Modules (SLM-318) can be added, expanding capacity to 954 intelligent addressable devices on three Signaling Line Circuit (SLC) loops. The panel ships with power supply PMB-AUX to support four NACs and two auxiliary outputs. Panels can be configured with just a few devices for small building applications or networked with many devices to protect a large campus or a high-rise office block. Simply add ad

We are engaged in offering Notifier CPU 2-3030D Card to our clients. Our range of all products is widely appreciated by our clients.

The NFS-320 and NFS-320R (Same as NFS-320 but in red enclosure) intelligent fire alarm control panels are part of NOTIFIER's UL listed ONYX Series. It's designed specifically for small applications with features that minimize installation time, enable faster response times, and simplify maintenance and usability.

Features & Benefits:

• Fully field programmable
• Removable chassis design for easy installation and service
• Direct connect to NOTIFIER FirstCommand™ Emergency Communications System
• Networkable with NOTI-FIRE-NET and ONYXWorks compatible up to 200 nodes for NFN
• Optional IP or GSM Communicator
• Listings: Releasing, Mass Notification, Seismic Certified, Marine Approved

We are engaged in offering FCM-1 Notifier Control Module to our clients. Our range of all products is widely appreciated by our clients.

The Notifier ISO-X(A) Fault Isolator Module is used with Notifier Onyx and CLIP series Fire Alarm Control Panels (FACPs) to protect the system against wire-to-wire short circuits on the SLC loops.

Features:

• Powered by SLC loop directly, no external power required.
• Base mounts on standard junction boxes (4.0"/10.16 cm square by 2.125"/5.398 cm deep).
• Integral LED blinks to indicate normal condition. Illuminates steady when short circuit condition is detected.
• High noise (EMF/RFI) immunity.
• Wide viewing angle of LED.
• SEMS screws with clamping plates for ease of wiring.
• Opens SLC loop automatically on detection of short, preventing the short from causing failure of the entire loop.
• Automatically resets on correction of short.
• Supports Style 4, 6, or 7 wiring.

The Notifier NBG-12LX is a state-of-the-art, dual-action (i.e.,requires two motions to activate the station) pull station that includes an addressable interface for any Notifier intelligent control panel except FireWarden series panels, and the NSP- 25 panel. Because the NBG-12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm.

We are engaged in offering NFS-320 Intelligent Addressable Fire Alarm Control Panel to our clients. Our range of all products is widely appreciated by our clients.

The NOTIFIER® FST-951 Series intelligent thermal detectors aredesigned for both performance and aesthetics, and are directreplacements for the FST-851 Series. A new modern, sleek, contemporarydesign and advanced thermal technologies make theFST-951 Series ideal for both system operation and building design.The point ID address, set using rotary decimal switches, providespecific detector locations.The series includes a 135°F/57°C fixed-temperature, rate-of-rise,and a 190°F/88°C fixed high-temperature detectors. These thermaldetectors provide effective, intelligent property protection in a varietyof applications. Detectors are available for both FlashScan® andCLIP applications as designated.

The LCM-320 Loop Control Module and the LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM320s and five LEM-320s. The LEM-320 module is used to expand the NFS-640/NFS2-640 to a second loop, and to expand each LCM-320 used on the NFS-3030/NFS2-3030 — each NFS-3030/NFS2-3030 LCM-320 supports an expansion LEM-320. 

Features:

• Up to 12,500 feet (3,810 m) on a Class B (Style 4) SLC loop (twisted-unshielded). 
• Built-in degraded mode increases survivability. 
• Very simple installation — plug-in style. 
• Permits multiple loops in small enclosure.

FSP-951 Smoke detector Make-Notifier The Notifier FSP-951 Series intelligent plug-in smoke detectors are designed for both performance and aesthetics, and are direct replacements for the FSP-851 Series. A new modern, sleek, contemporary design and enhanced optical sensing chamber is engineered to sense smoke produced by a wide range of combustion sources in accordance with more stringent code standards. The FSP-951 Series detector sensitivity can be programmed in the control panel software. Sensitivity is continuously monitored and reported to the panel. Point ID capability allows each detector’s address to be set with rotary, decimal address switches, providing exact detector location for selective maintenance when chamber contamination reaches an unacceptable level. Dual electronic thermistors add 135°F (57°C) fixed temperature thermal sensing on the FSP-951T. The FSP-951R is a remote test capable detector for use with DNR Series duct detector housings. FSP-951 series detectors are available for both FlashScan® and CLIP applications as designated. 

Features SLC LOOP: 

• Two-wire SLC loop connection 
• Unit uses base for wiring 
• Compatible with FlashScan® and CLIP protocol systems 
• Stable communication technique with noise immunity 

Addressing:

• Addressable by device 
• Rotary, decimal addressing (Refer to the NOTIFIER panel manuals for device capacity.)

We are engaged in offering FSP-951T Notifire Multi Detector to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering Notifier FMM-101A Addressable Monitor Module to our clients. Our range of all products is widely appreciated by our clients.

The LCM-320 Loop Control Module and the LEM-320 Loop Expander Module provide NOTIFIER’s ONYX® Series of Fire Alarm Control Panels (FACPs) with Signaling Line Circuits (SLCs). The ONYX® Series NFS-640/NFS2-640 supports one LEM-320; the NFS-3030/NFS2-3030 supports up to five LCM- 320s and five LEM-320s. The LEM-320 module is used to expand the NFS-640/NFS2-640 to a second loop, and to expand each LCM-320 used on the NFS-3030/NFS2-3030 — each NFS-3030/NFS2-3030 LCM-320 supports an expansion LEM-320.

• Up to 12,500 feet (3,810 m) on a Class B (Style 4) SLC loop (twisted-unshielded).
• Built-in degraded mode increases survivability.
• Very simple installation — plug-in style.
• Permits multiple loops in small enclosure.

The NFS2-3030 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. Fire emergency detection and evacuation are extremely critical to life safety, and the NFS2-3030 is ideally suited for these applications. The NFS2-3030 is part of the ONYX® Series of products from NOTIFIER. The NFS2-3030 is ideal for virtually any application because it features a modular design that is configured per project requirements. With one to ten Signaling Line Circuits (SLCs), the NFS2-3030 supports up to 3,180 intelligent addressable devices.

Information is critical to fire evacuation personnel, and the NFS2-3030’s large 640-character Liquid Crystal Display (LCD) presents vital information to operators concerning a fire situation, fire progression, and evacuation details.

A host of other options are available, including single- or multi-channel voice; firefighter’s telephone; LED, LCD, or PC-based graphic annunciators; networking; advanced detection products for challenging environments; wireless fire protection; and many additional options.

The Notifier FSB-200 and FSB-200S are intelligent, addressable reflected beam smoke detectors for protecting open areas with high and sloping ceilings, and wide-open areas, where spot-type smoke detectors are difficult to install and maintain. Ideal applications are atriums, cathedral ceilings, aircraft hangars, warehouses, sporting arenas, concert halls, and enclosed parking facilities. They are compatible with the NFS-3030, NFS2-3030, NFS-640, NFS2- 640, and NFS-320 in FlashScan® or CLIP mode, as well as legacy addressable panels. Installation of the single-ended reflective design is much quicker than a dual-ended projected beam detector. Alignment is easily accomplished with an optical sight and a two-digit signal strength meter incorporated into the beam detector. Listed for operation from –22°F to 131°F, the FSB-200 and FSB-200S are usable in open area applications where temperature extremes exceed the design limits of other types of smoke detection.

The FSB-200 and FSB-200S are a transmitter/receiver unit and a reflector. When smoke enters the area between the unit and the reflector it causes a reduction in the signal strength. When the smoke level (signal strength) reaches the predetermined threshold, an alarm is activated. The detectors have four standard sensitivity selections as well as two Acclimate® settings. When either Acclimate® setting is selected, the detector’s advanced software algorithms automatically adjust to the optimum sensitivity for the specific environment.

FSCO-951 and FSCO-951A are intelligent, addressable carbonmonoxide (CO) detectors with integral communication to providepoint location for alarm communication and selective maintenance.These detectors have point ID capability that enables each detectoraddress to be set with rotary address switches providing exactdevice locations. The modern design and expanded color optionssupport contemporary aesthetic demands. In addition, each detectoris constructed for exceptional installation and maintenance efficiency.The FSCO-951 incorporates carbon monoxide (CO) detection principlesmeeting the UL 2075 standard for system-connected lifesafety carbon monoxide detection. FSCO-951A meets Canadianstandard CAN/ULC-S588. As an addressable detector, additionalmodules are not needed for point ID which streamlines the installationprocess. This allows you to upgrade your addressable fire systemto meet new CO code requirements in applications with fuelburning equipment such as furnace areas and laundry rooms.Released through the incomplete burning of various fuels, CO is acolorless, odorless and deadly gas that is virtually impossible todetect with the human senses. Because the potential exists fordangerous levels of CO to accumulate in almost any building, legislationmandating the use of CO detection in commercial spacescontinues to grow.FSCO-951 is recommended for use in conjunction with B200Sseries intelligent sounder bases. For Canadian applications, useB200SCOA series with FSCO-951A. These bases can generate aTemp 4 pattern for CO alarm indication. They recognize the SystemSensor synchronization protocol.

We are engaged in offering Notifier F/MCP/Glass Manual Call Point to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering Notifier Manual Call Point to our clients. Our range of all products is widely appreciated by our clients.

We are engaged in offering FMM-1 Notifier Monitor Module to our clients. Our range of all products is widely appreciated by our clients.

The Notifier NBG-12LX is a state-of-the-art, dual-action (i.e., requires two motions to activate the station) pull station that includes an addressable interface for any Notifier intelligent control panel except FireWarden series panels, and the NSP- 25 panel. Because the NBG-12LX is addressable, the control panel can display the exact location of the activated manual station. This leads fire personnel quickly to the location of the alarm.

Features:

• Maintenance personnel can open station for inspection and address setting without causing an alarm condition.
• Built-in bicolor LED, which is visible through the handle of the station, flashes in normal operation and latches steady red when in alarm.
• Handle latches in down position and the word “ACTIVATED” appears to clearly indicate the station has been operated.
• Captive screw terminals wire-ready for easy connection to SLC loop (accepts up to 12 AWG/3.25 mm² wire).
• Can be surface mounted (with SB-10 or SB-I/O) or semiflush mounted. Semi-flush mount to a standard singlegang, double-gang, or 4" (10.16 cm) square electrical box.
• Smooth dual-action design.
• Meets ADAAG controls and operating mechanisms guidelines (Section 4.1.3[13]); meets ADA requirement for 5 lb. maximum activation force.
• Highly visible.
• Attractive shape and textured finish.
• Key reset.
• Includes Braille text on station handle.
• Optional trim ring (BG12TR).
• Meets UL 38, Standard for Manually Actuated Signaling Boxes.
• Up to 99 NBG-12LX stations per loop on CLIP protocol loops.
• Up to 159 NBG-12LX stations per loop on FlashScan® protocol loops.
• Dual-color LED blinks green to indicate normal on FlashScan® systems.

Keyboard display module - Notifier KDM-R2The KDM-R2 is an 80-character backlit LCD display with QWERTY programming and control keypad. Order two BMP-1 blank modules and DP-DISP2 mounting plate separately. Requires top row of a cabinet. Required for each stand-alone 80-character display system. The KDM-R2 may mount in network nodes to display “local” node information as long as at least one NCA-2 or NCS/ONYXWorks network display is on the system to display network information. (Non-English versions also available: KDM-R2C for ULC application, KDM-R2-FR, KDM-R2-PO, KDM-R2-SP.)

General The NFS2-3030 is an intelligent Fire Alarm Control Panel (FACP) designed for medium- to large-scale facilities. Fire emergency detection and evacuation are extremely critical to life safety, and the NFS2-3030 is ideally suited for these applications. The NFS2-3030 is part of the ONYX® Series of products from NOTIFIER. The NFS2-3030 is ideal for virtually any application because it features a modular design that is configured per project requirements. With one to ten Signaling Line Circuits (SLCs), the NFS2-3030 supports up to 3,180 intelligent addressable devices. Information is critical to fire evacuation personnel, and the NFS2-3030’s large 640-character Liquid Crystal Display (LCD) presents vital information to operators concerning a fire situation, fire progression, and evacuation details. A host of other options are available, including single- or multichannel voice; firefighter’s telephone; LED, LCD, or PC-based graphic annunciators; networking; advanced detection products for challenging environments; wireless fire protection; and many additional options.